Design Gallery

This custom setup will utilize a set of 5" tall custom made LEDs in the side flange of each fender. Have Bad Dad install our Upgraded Wiring Harness which will make these custom taillights operate as run light, brake lights & turn signals. This setup is available in both our Bagger Fenders and Summit Fenders for all models.

Your new flush mounted parts will arrive with everything pre-drilled and pre-fit, all lights flush mounted, all bodywork complete, and the parts will be in a final primer and ready to go to paint. We can pre-wire the taillights into one of our plug-n-play wiring harnesses which will serve as a direct plug-in for your stock wiring harness. Our custom harness also features a load equalizer for the LEDs and quick disconnect clips for the saddlebag lights.

These custom parts are proudly made in the USA and hand built in Indiana.

This custom setup will utilize a set of 10" tall custom made LEDs in the side flange of each fender. Each LED assembly features 80 LEDs for a total of 160 LEDs on the back of this fender. Have Bad Dad install our Upgraded Wiring Harness which will make these custom taillights operate as run light, brake lights & turn signals. This setup is available in both our Bagger Fenders and Summit Fenders for all models (shown here with Summit Fender).

Your new flush mounted parts will arrive with everything pre-drilled and pre-fit, all lights flush mounted, all bodywork complete, and the parts will be in a final primer and ready to go to paint. We can pre-wire the taillights into one of our plug-n-play wiring harnesses which will serve as a direct plug-in for your stock wiring harness. Our custom harness also features a load equalizer for the LEDs and quick disconnect clips for the saddlebag lights.

These custom parts are proudly made in the USA and hand built in Indiana.

This custom setup will utilize a set of 10" tall custom made LEDs in the side flange of each fender. Each LED assembly features 80 LEDs for a total of 160 LEDs on the back of this fender. Have Bad Dad install our Upgraded Wiring Harness which will make these custom taillights operate as run light, brake lights & turn signals. This setup is available in both our Bagger Fenders and Summit Fenders for all models (shown here with Summit Fender).

Your new flush mounted parts will arrive with everything pre-drilled and pre-fit, all lights flush mounted, all bodywork complete, and the parts will be in a final primer and ready to go to paint. We can pre-wire the taillights into one of our plug-n-play wiring harnesses which will serve as a direct plug-in for your stock wiring harness. Our custom harness also features a load equalizer for the LEDs and quick disconnect clips for the saddlebag lights.

These custom parts are proudly made in the USA and hand built in Indiana.

This custom setup will utilize a set of 10" tall custom made LEDs in the side flange of each fender. Each LED assembly features 80 LEDs for a total of 160 LEDs on the back of this fender. Have Bad Dad install our Upgraded Wiring Harness which will make these custom taillights operate as run light, brake lights & turn signals. This setup is available in both our Bagger Fenders and Summit Fenders for all models (shown here with Bagger Fender).

Your new flush mounted parts will arrive with everything pre-drilled and pre-fit, all lights flush mounted, all bodywork complete, and the parts will be in a final primer and ready to go to paint. We can pre-wire the taillights into one of our plug-n-play wiring harnesses which will serve as a direct plug-in for your stock wiring harness. Our custom harness also features a load equalizer for the LEDs and quick disconnect clips for the saddlebag lights.

These custom parts are proudly made in the USA and hand built in Indiana.

This setup uses 7" wide by 4" tall brake light with 80 LEDs. The turn signals are then flush mounted into the side flanges of the rear fender. This setup is available in both our Bagger Fenders and Summit Fenders for all models.

Your new flush mounted parts will arrive with everything pre-drilled and pre-fit, all lights flush mounted, all bodywork complete, and the parts will be in a final primer and ready to go to paint. We can pre-wire the taillights into one of our plug-n-play wiring harnesses which will serve as a direct plug-in for your stock wiring harness. Our custom harness also features a load equalizer for the LEDs and quick disconnect clips for the saddlebag lights.

These custom parts are proudly made in the USA and hand built in Indiana.

This setup uses 7" wide by 4" tall brake light with 80 LEDs. The turn signals are then flush mounted into the side flanges of the rear fender. This setup is available in both our Bagger Fenders and Summit Fenders for all models.

Your new flush mounted parts will arrive with everything pre-drilled and pre-fit, all lights flush mounted, all bodywork complete, and the parts will be in a final primer and ready to go to paint. We can pre-wire the taillights into one of our plug-n-play wiring harnesses which will serve as a direct plug-in for your stock wiring harness. Our custom harness also features a load equalizer for the LEDs and quick disconnect clips for the saddlebag lights.

These custom parts are proudly made in the USA and hand built in Indiana.

This setup uses 7" wide by 4" tall brake light with 80 LEDs. The turn signals are then flush mounted into the side flanges of the rear fender. This setup is available in both our Bagger Fenders and Summit Fenders for all models (shown here with Bagger Fender).

Your new flush mounted parts will arrive with everything pre-drilled and pre-fit, all lights flush mounted, all bodywork complete, and the parts will be in a final primer and ready to go to paint. We can pre-wire the taillights into one of our plug-n-play wiring harnesses which will serve as a direct plug-in for your stock wiring harness. Our custom harness also features a load equalizer for the LEDs and quick disconnect clips for the saddlebag lights.

These custom parts are proudly made in the USA and hand built in Indiana.

This setup uses our 7" wide by 4" tall brake light. It also utilizes a set of 10" tall custom made LEDs in each side flange of the fender. This taillight and turn signal combo uses a total of 240 LEDs between the three taillights. This setup is available in both our Bagger Fenders and Summit Fenders for all models (shown here with our Summit Fender).

Your new flush mounted parts will arrive with everything pre-drilled and pre-fit, all lights flush mounted, all bodywork complete, and the parts will be in a final primer and ready to go to paint. We can pre-wire the taillights into one of our plug-n-play wiring harnesses which will serve as a direct plug-in for your stock wiring harness. Our custom harness also features a load equalizer for the LEDs and quick disconnect clips for the saddlebag lights.

These custom parts are proudly made in the USA and hand built in Indiana.

This setup uses our 7" wide by 4" tall brake light with 80 LEDs. The turn signals are then flush mounted into the back of the Stretched Bags. This setup is available in both our Bagger Fenders and Summit Fenders for all models (shown here with Bagger Fender).

Your new flush mounted parts will arrive with everything pre-drilled and pre-fit, all lights flush mounted, all bodywork complete, and the parts will be in a final primer and ready to go to paint. We can pre-wire the taillights into one of our plug-n-play wiring harnesses which will serve as a direct plug-in for your stock wiring harness. Our custom harness also features a load equalizer for the LEDs and quick disconnect clips for the saddlebag lights.

These custom parts are proudly made in the USA and hand built in Indiana.

This setup uses our 7" wide by 4" tall brake light with 80 LEDs. The turn signals are then flush mounted into the back of the Stretched Bags. This setup is available in both our Bagger Fenders and Summit Fenders for all models (shown here with Bagger Fender).

Your new flush mounted parts will arrive with everything pre-drilled and pre-fit, all lights flush mounted, all bodywork complete, and the parts will be in a final primer and ready to go to paint. We can pre-wire the taillights into one of our plug-n-play wiring harnesses which will serve as a direct plug-in for your stock wiring harness. Our custom harness also features a load equalizer for the LEDs and quick disconnect clips for the saddlebag lights.

These custom parts are proudly made in the USA and hand built in Indiana.

This setup uses our 7" wide by 4" tall brake light with 80 LEDs. The turn signals are then flush mounted into the Stretched Saddlebags (shown here with 4" wide by 2" tall lights; also available with 4" round lights). This setup is available in both our Bagger Fenders and Summit Fenders for all models.

Your new flush mounted parts will arrive with everything pre-drilled and pre-fit, all lights flush mounted, all bodywork complete, and the parts will be in a final primer and ready to go to paint. We can pre-wire the taillights into one of our plug-n-play wiring harnesses which will serve as a direct plug-in for your stock wiring harness. Our custom harness also features a load equalizer for the LEDs and quick disconnect clips for the saddlebag lights.

These custom parts are proudly made in the USA and hand built in Indiana.

This setup uses a custom version of our standard taillight and is oversized to measure 7" wide by 8" tall and features 160 LEDs. The turn signals are then flush mounted into the Stretched Saddlebags (shown here with 4" wide by 2" tall lights; also available with 4" round lights). This setup is available in both our Bagger Fenders and Summit Fenders for all models.

Your new flush mounted parts will arrive with everything pre-drilled and pre-fit, all lights flush mounted, all bodywork complete, and the parts will be in a final primer and ready to go to paint. We can pre-wire the taillights into one of our plug-n-play wiring harnesses which will serve as a direct plug-in for your stock wiring harness. Our custom harness also features a load equalizer for the LEDs and quick disconnect clips for the saddlebag lights.

These custom parts are proudly made in the USA and hand built in Indiana.

This setup uses our popular bolt-on surface mounted 992 Taillights. Have Bad Dad add its Upgraded Wiring Harness which will make these custom taillights operate as run light, brake lights & turn signals. This setup is available in any of Bad Dad's rear fenders, including the Bagger Fender, Summit Fender, and Competition Series Fenders.

Your new Rear Fender & Stretched Bags will arrive with all of the mounting holes pre-drilled & pre-fit for an easy installation. Bad Dad's Stretched Bags are finished in a final primer surface finish which is ready to go directly to paint. Our custom harness also features a load equalizer for the LEDs and quick disconnect clips for the saddlebag lights.

These custom parts are proudly made in the USA and hand built in Indiana.

This setup uses our popular bolt-on surface mounted 957 Taillights. Have Bad Dad install our Upgraded Wiring Harness which will make these custom taillights operate as run light, brake lights & turn signals. This setup is available in both our Bagger Fenders and Summit Fenders for all models (shown here with our Summit Fender).

Your new flush mounted parts will arrive with everything pre-drilled, pre-fit, and all lighting ready to bolt into the fender. We can pre-wire the taillights into one of our plug-n-play wiring harnesses which will serve as a direct plug-in for your stock wiring harness. Our custom harness also features a load equalizer for the LEDs and quick disconnect clips for the saddlebag lights.

These custom parts are proudly made in the USA and hand built in Indiana.

This setup uses our 7" wide by 4" tall brake light. It also utilizes a set of our popular bolt-on surface mounted 957 Taillights. This setup is available in both our Bagger Fenders and Summit Fenders for all models (shown here with our Summit Fender).

Your new flush mounted parts will arrive with everything pre-drilled and pre-fit, all lights flush mounted, all bodywork complete, and the parts will be in a final primer and ready to go to paint. We can pre-wire the taillights into one of our plug-n-play wiring harnesses which will serve as a direct plug-in for your stock wiring harness. Our custom harness also features a load equalizer for the LEDs and quick disconnect clips for the saddlebag lights.

These custom parts are proudly made in the USA and hand built in Indiana.